收藏本站
16 Mbit LPC Serial Flash
A Microchip Technology Company
SST49LF016C
Data Sheet
Read-Array Command
Upon initial device power-up and after exit from reset, the device defaults to the read array mode. This
operation can also be initiated by writing the Read-Array command. (See Table 8.) The device remains
available for array reads until another command is written. Once an internal Program/Erase operation
starts, the device will not recognize the Read-Array command until the operation is completed, unless
the operation is suspended via a Program/Erase Suspend command.
Read-Software-ID Command
The Read-Software-ID operation is initiated by writing the Read-Software-ID command. Following the
command, the device will output the manufacturer’s ID and device ID from the addresses shown in
Table 9. Any other valid command will terminate the Read-Software-ID operation.
The Read-Software-ID command is the same as the Read-Security-ID command. See “Security ID
Commands” on page 19.
Table 9: Product Identification
Address 1
Data
Manufacturer’s ID
Device ID
SST49LF016C
FFFC 0000H
FFFC 0001H
BFH
5CH
T9.1 25029
1. Address shown in this column is for boot device only. Address locations should appear elsewhere in the 4 GByte sys-
tem memory map depending on ID strapping values on ID[3:0] pins when multiple LPC memory devices are used in a
system.
Read-Status-Register Command
The Status register may be read to determine when a Sector-/Block-Erase or Program completes, and
whether the operation completed successfully. The Status register may be read at any time by writing
the Read-Status-Register command. After writing this command, all subsequent Read operations will
return data from the Status register until another valid command is written.
The default value of the Status register after device power-up or reset is 80H.
?2011 Silicon Storage Technology, Inc.
17
DS25029A
06/11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SST49LF080A-33-4C-WHE-T IC FLASH SER LPC 8MBIT 32TSOP
SST49LF160C-33-4C-NHE IC FLASH SER LPC 16MBIT 32PLCC
ST40 DIAC 35-45V BILATERAL TRIG DO214
STRIKER SURGE SUPPRESSR 120V 7OUT 6'CORD
SUPER-7 SURGE SUPPRESSOR 7 OUT 7' CORD
SUPER6TEL12 SURGE SUPPR 7OUT 12'CORD W/RJ11
SUPER6TEL SURGE SUPPRESSOR 7OUT W/TEL
SUPER7COAX SURGE SUPPRESSOR 7 OUT W/COAX
相关代理商/技术参数
SST49LF016C-33-4C-NHE 功能描述:闪存 16M (2Mx8) 33MHz 3.0-3.6V Commercial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF016C-33-4C-NHE-T 功能描述:闪存 3.0 to 3.6V 16Mbit LPC Firmware 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF016C-33-4C-WHE 功能描述:闪存 16M (2Mx8) 33MHz 3.0-3.6V Commercial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF016C-33-4C-WHE_ 制造商:Microchip Technology Inc 功能描述:
SST49LF016C-33-4C-WHE-T 功能描述:闪存 3.0 to 3.6V 16Mbit LPC Firmware 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF016C-66-4C-NHE 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit LPC Serial Flash
SST49LF016C-66-4C-WHE 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:16 Mbit LPC Serial Flash
SST49LF020 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:2 Megabit LPC Flash